How To Install A Kelvinator Window Air Conditioner

                                  kelvinator Window Wall Electronic Room Air Conditioner User Manual                              

Congratulations

Congratulations and thank you for choosing our Electrical Window Wall room air conditioner. We are certain y'all will find your new air conditioner a pleasure to use. Before yous use the air conditioner, nosotros recommend that y'all read through the entire user manual, which provides the description of the air conditioner and its functions.

To avoid the risks that are always nowadays when you use an electric appliance, it is important that the air conditioner is installed correctly and that you lot read the safe instructions advisedly to avoid misuse and hazards.

We recommend that you lot keep this instruction booklet for time to come reference and pass it on to any future owners.

Afterwards unpacking the air conditioner please check it is not damaged. If in doubt, do not apply the air conditioner just contact your local Electrolux Client Care Centre.

Environmental tip

Data on disposal for users

• Most of the packing materials are recyclable. Please dispose of those materials through your local recycling depot or by placing them in advisable collection containers.
• If you lot wish to discard this air conditioner, please contact your local authorities and inquire for the correct method of disposal.
• This product contains refrigerant which must be reclaimed by a licensed refrigeration mechanic earlier the product can be disposed of.

Refrigerant warning

This unit of measurement uses refrigerant R32 and must exist disposed of by a licensed refrigeration mechanic with cognition of advisable gas reclamation methods.

Circumspection

• The air conditioner is not intended for use past immature children or infirmed persons without supervision.
• Young children should be supervised to ensure that they exercise non play with the air conditioner.
• Contact an authorised installer for installation of this unit.
• Contact an authorised service technician for repair or maintenance of this unit.
• If the power string is to be replaced, replacement work must be performed by authorised personnel only.
• Installation work must be performed in accordance with the national wiring Standards by authorised personnel only.

Important Information that may impact your Manufacturer's Warranty

Adherence to the directions for utilize in this manual is extremely important for health and condom. Failure to strictly adhere to the requirements in this manual may consequence in personal injury, belongings damage and bear on your ability to make a claim under the Kelvinator manufacturer's warranty provided with your production. Products must be used, installed and operated in accordance with this manual. You lot may not be able to claim on the Kelvinator manufacturer's warranty in the result that your product fault is due to failure to adhere to this manual.

Safety precautions

Caution

• Contact an authorised service technician for repair or maintenance of this unit of measurement.
• Contact a licensed installer for installation of this unit.
• The air conditioner is not intended for use by young children or infirmed persons without supervision.
• Young children should be supervised to ensure that they practice not play with the air conditioner.
• This air conditioner must exist installed in accordance with As/NZS 3000:2000 and your electricity suppliers rules.
• There are local quango rules regarding maximum allowable noise levels emitted by air conditioners.
• If the power cord is to be replaced, replacement work shall be performed by authorised personnel only.
• Installation work must be performed in accord with the national wiring standards by authorised personnel only. Wrong connectedness can crusade overheating or fire.

Inside this manual you will discover many helpful hints on how to use and maintain your air conditioner properly.

Only a little preventative care on your function can save yous a great deal of fourth dimension and money over the life of your air conditioner. You'll detect many answers to common problems in the chart of troubleshooting tips. If you review the nautical chart of Troubleshooting Tips beginning, you may not need to call for service.

Meanings of symbols used in this manual are shown below:

Circumspection

Prior to Operation

Preparing for operation

1. Contact an authorised installation specialist for installation.
2. Plug in the power plug properly.
3. Do not use a damaged or not-standard power cord.
4. Do non share the same outlet with other appliances.
5. Do not use an extension cord.
6. Do not commencement/finish operation past plugging /unplugging the power cord.

Usage

1. Exposure to direct airflow to occupants, pets or plants for an extended period of time could be hazardous to their wellness.
2. Due to the possibility of oxygen deficiency, ventilate the room when used together with stoves or other heating devices.

Cleaning and maintenance

1. Practise non touch the metal parts of the unit when removing the filter. Injuries can occur when treatment sharp metallic edges.
2. Exercise not use water to make clean inside the air conditioner. Exposure to water tin can destroy the insulation, leading to possible electric shock. 3 When cleaning the unit, offset make sure that the power and excursion billow are turned off.

Operating temperature

Unit parts identification

ane Front panel
two Air filter
3 Frame
iv Cabinet
5 Air inlet grille (outdoor side)
6 Air outlet grille
7 Electronic control keypad
8 Power supply cord and plug
9 Remote control

1. Power cord conductors are distinguished according to colour as follows (see Fig.one)
2. For your safety and protection, this unit of measurement is earthed through the ability string (see Fig.2) Please contact the manufacturer or its service amanuensis or a similar qualified person if you want to supersede information technology.
3. Be sure that the unit is being correctly grounded. The wall outlet (Air-Intermission Switch) should be provided with reliable earth wire.
4. The unit should be provided with an individual circuit and the circuit billow/fuse rating should be the same as that of the power string and wall outlet.

Operating instructions

Controls
The electronic control keypad will look like i of the post-obit:

Contrary Cycle Models

Cooling simply models

Vent command
The vent control is located above the control knobs. The operation method is dissimilar on unlike models (come across the following figures).

For maximum cooling efficiency, Shut the vent. This will allow internal air circulation.

To open the vent, pull the lever toward you To close it, push button it in.

To open the vent, prepare the lever to the right position To close it, set the lever in the left position.

Operating instructions

Ability: Printing the Power keypad to turn the unit on/off. (The TIMER keypad controls the automobile commencement/stop feature of the unit of measurement.)

Fashion: Press the "MODE" keypad to select the appropriate operating mode. For the Reverse Cycle models (cooling & heating), the mode selection will alternate between AUTO, HEATING, COOLING, FAN and DRY. For the Cooling only models, select the operating mode from AUTO, COOLING, FAN and DRY. The green indicator light beside the "Style" choice will illuminate, identifying the mode selected.

When using the Dry and AUTO mode, you cannot select a fan speed. The fan motor operates on Low speed in Dry style and on MED speed in Machine mode.

Annotation: There is no green indicator light for "Car" mode. When you select "Auto " mode, a beep will sound indicating this "Way" option was selected.

+ Temperature settings upwardly: Printing the + keypad to increase the gear up (operating) temperature of the unit of measurement.
Each time the keypad is pressed the temperature increases by 1°C with a maximum setting of 30°C­

– Temperature settings downwardly: Printing the –­ keypad to decrease the set (operating) temperature of the unit.
Each time the keypad is pressed the temperature decreases by 1°C with a maximum setting or minimum temperature of 16°C

Fan:
Press this keypad button to activate the appropriate fan speed setting. Each printing of the button will alternate through Depression, MED, High fan speed options. The dark-green indicator light beside the FAN speed pick will illuminate, identifying the fan speed selected.
Swing: Press the "SWING" keypad to activate the automatic air swing (oscillation) feature.

The green indicator lite adjacent to the "SWING" keypad will illuminate, identifying that the selected mode is operational. The vertical louvers will oscillate dorsum and forth (side to side) automatically sweeping air around for comfy cooling/heating. To stop the air swing feature, pressing the "SWING" keypad again, the green indicator light adjacent to the keypad volition go off.

When the SLEEP mode is activated, the light-green indicator calorie-free beside the "SLEEP" function will illuminate.

Timer: Press the "TIMER" keypad to activate the "auto get-go/auto stop" timer function.

Auto outset/cease programs can be set from i/2-12 hours. Each press of the "TIMER" keypad volition increment the selected time in one/2 hour increments.

Dry: In the Dry manner, the air conditioner will operate in the form of a dehumidifier. Since the conditioned space is a closed or sealed area, some caste of cooling volition go along.

Cooling: The temperature settings are adaptable between 16°C to 30°C . Cooling begins automatically when the room temperature is 1°C to a higher place the fix point, and stops when the room temperature is ane°C below the set bespeak. The fan volition non cease running.

Heat: The temperature settings are adjustable between sixteen°C to thirty°C in heating mode. The default temperature setting is 24°C in heating mode and the fan speed is optional.

Note: When heating stops, there may be a slight filibuster of thirty seconds for the fan motor to stop.

Automobile: For the cooling merely models, after selecting "Automobile" by pressing the "MODE" push, the air conditioner volition select the appropriate operating way from "FAN", "COOL" or "DRY" based upon the temperature difference between the actual and desired room temperature.

For the cooling and heating models, after selecting "Automobile" past pressing the "Way" button, the air conditioner wioll select the advisable style for cool, heat or dry based upon the temperature divergence between the actual and desired room temperature. The default heating temperature set point is 20°C, the default cooling temperature set point is 25°C

Note: When activating the SLEEP mode when the unit is in AUTO mode, the fan motor will change into Depression speed mode immediately.

Sleep:
Press and hold the "SWING" keypad for two seconds or apply the remote control to actuate the "Slumber" feature . Press and agree the "SWING" keypad or use the remote control once more for 2 seconds to conciliate the "SLEEP" feature. In the Cooling fashion, the cooling temperature set bespeak will increase 1OC per hour after the "Sleep" manner is selected.

Ii hours later, the set up betoken will continue at this temperature and the fan motor will remain on Depression speed. In the Heating mode, the heating temperature prepare point will subtract 1OC per hour after the "Sleep" mode is selected. Two hours later, the ready point volition continue at this temperature and the fan motor will remain on LOW speed. Using the "Sleep" style volition reduce racket creating a comfortable sleeping environment.

Notation: When activating the SLEEP style in Auto manner, the set temperature volition non change over time.

The mitt held remote control unit allows you to control all operational aspects of your Air Conditioner, from the convenience of your favourite armchair. Here are some things you lot should know nigh how to operate your Air Conditioner with the hand held remote control.

Temperature:
+ Increases / ­ Decreases operating TEMPERATURE just.

Ability ON/OFF:
Turns the power to the primary unit "on/off" only.

Way:
Activates the "AUTO" (if applicable), "HEAT" (if applicable), "COOL", "FAN" or "DRY" office.

Timer ON/ Timer OFF:
Activates the "motorcar Get-go" or "car Stop" program from 0-12 hours (1 hr increments).

Sleep:
Activates the "SLEEP" mode.

Swing:
Activates the automatic air SWING (vertical) louver oscillation) feature.

Fan:
Activates the FAN speed settings (High, MED, LOW, AUTO).

Batteries:
To operate the hand held remote control, you will require two AAA 1.5Volt batteries (included).

NOTE: Batteries should exist replaced when:

a) No signal (beep) is heard from the chief unit of measurement when initiating programme commands from the remote control to the chief unit of measurement.
b) The chief unit does not respond to the remote control plan commands.

Battery Replacement:

1. Slide the lower (battery) cover down (Located on rear of remote control unit).
2. Insert 2 "AAA" Batteries within the battery sleeping accommodation (equally depicted inside the battery sleeping room).
3. Re-install lower battery comprehend. 4 If the remote control is not being used for extended time periods, (vacation, off flavour) the batteries should be removed from the remote control unit.

Remote Control Operating Instructions:

The hand held remote control unit operates within a range of 7 metres (23ft) from the receiver located within the unit. Any obstruction between the receiver and the hand held remote may cause signal interference, limiting the power to program the main unit of measurement.
Each fourth dimension a remote control button is pressed, a beep will sound indicating a command (betoken) is transmitted and received on the unit. When the command is received, the appropriate role will be displayed (temporarily) in the LED display window and the dark-green indicator light corresponding to the selection mode volition illuminate on the main control panel.

Note: The LED display will default to show the ambient room temperature within 10 seconds of all program commands.

Power: To plough the (air conditioner) power on/off, aim the remote command at the receiver (window) on the unit and press the "Power" push.

Mode: Press the "MODE" button to select either "AUTO", "HEATING", "COOLING", "FAN" or "Dry out" mode (Cooling & Heating model) or "COOLING", "FAN" or "DRY" style (Cooling only model).

Set cooling/heating/auto temperature: Printing the "TEMP" (up/downward) buttons to select (increase/ decrease) the required operating temperature, the selected temperature will appear (temporarily) in the LED display.

The temperature settings are adaptable between 16OC and 31OC.

Fan: Printing the "FAN" button to select the required operating fan speed (Loftier, MED or LOW).

Swing: Printing the "SWING" push to activate the swing feature (the vertical louvres will oscillate automatically from side to side). Press the "SWING" button over again to deactivate the "SWING" characteristic.

Timer: Printing the "TIMER" button to activate the "auto start/auto stop" timer function.

Timer OFF :(simply available when the unit is on) Press the "TIMER OFF" push to actuate the auto stop timer function. THe method of setting is the same as above for "TIMER ON".

Sleep:
Press the "Slumber" push to actuate the "SLEEP" feature.
Printing the "Slumber" button to deactivate the "Slumber" feature.
In Cooling style, the cooling temperature fix point will increase 1 (degree symbol) C per 60 minutes after the "SLEEP" mode is selected. Later on two hours, the prepare temperature will remain constant. In Heating mode, the heating temperature set point will decrease 1 (degree symbol)C per hr after the sleep button is pressed and and so remain constant.

Free energy Saver: (only available in "COOLING" and "Dry" fashion)
Press the ENERGY SAVER button to activate or deactivate the "Free energy SAVER" function. In this manner, the fan volition keep to run for i minute subsequently the compressor shuts off.

Calorie-free: Press this button at start upwards and the light on the air conditioner volition be turned on or off. Light On is the default at commencement up.

Clock: Press this push button, the clock can be set up, icon (image of clock face up required) blinks. Inside five seconds, the fourth dimension can exist
adjusted by pressing the + or ­ buttons, if you continuously printing ane of these buttons, later on 2 seconds , for every i/2 second, the time will be increased or decreased by one minute. If you are withal pressing the button after the fourth dimension has changed by ten minutes, the fourth dimension value volition increase or subtract in 10 minutes steps. While the icon continues to glimmer, repressing the clock button will terminate the blinking and the clock will be set.

Special Locking Role:
Press the + or ­ push simultaneously to lock or unlock the keypad. If the remote control is locked, the (insert padlock icon) will be displayed on information technology, in that case, press any button, the icon will flicker 3 times. Repress the two buttons simultaneously to unlock.

To change Celcius to Farenheit
With the air conditoner switched off, press the "MODE" and buttons simultaneously to switch °C and °F.

Circumspection
NEVER operate the air conditioner without the air filter, equally dust/dirt particles tin can contribute to equipment failure.

Vertical air flow adjustment (manually)
To adjust the vertical air flow management, adjust any 1 of the horizontal louvre blades. When adjusting the horizontal louver blades upwards or down, always go on the top or bottom blades horizontal. This can effectively foreclose water droplets condensing on the front end panel of the unit of measurement.

Maintenance

Air Filter
The air filter behind the inlet grille should be checked and cleaned at to the lowest degree once every 2 weeks (or equally necessary) to maintain optimal performance of the air conditioner.

Removing the air filter
The filter LED will light upwardly later 250hrs of performance to remind the customer to clean the filter. Clean the filter following the instructions below, then printing the filter button next to the LED to reset the clean filter indicator.

1. The Grille can be opened from the lesser for easy maintenance sfter installation.
2. Open the inlet grille by pulling on the openings in the bottom of the grille
3. Pull the tab slightly to release the filter. Pull the filter frontward to remove it.
4. Make clean the filter with warm soapy water. The water should be below xl°C to prevent damage.
5. Rinse off and gently milkshake off any excess h2o from the filter. Allow the filter to dry before replacing information technology. To prevent damage, do not dry in direct sunlight.

AUTO restart
During a power failure, the air conditioner volition terminate completely. When the power is restored, the air conditioner volition start automatically with all the previous settings preserved in the retention.

The treatment of condensed h2o

1. Take out the drain pan and screws (provided within your air conditioner accessories bag)
2. Install the drain pan at the bottom of the unit and secure it with the screws provided.
3. Connect a suitable sized drain hose (not supplied) to the drain outlet located on the underside of the drain pan.

Installation instructions

Select the all-time location

1. To avoid vibration and racket, make sure the unit is installed securely and firmly.
2. Install the unit where the sunlight does not shine directly on the unit. If the unit receives direct sunlight, build an canopy to shade the cabinet.
3. There should be no obstacle, such as a fence or wall, inside 50cm from the back of the cabinet because information technology will foreclose heat radiations of the condensor. Restriction of outside air volition profoundly reduce the cooling and heating efficiency of the air conditioner.
4. Install the unit a piffling obliquely outward non to leak the condensed water into the room (about 10mm or 1/4 chimera with level).
5. Install the unit of measurement with its lesser portion 75~150cm above the floor level.
6. The power string must be connected to an independent circuit. The xanthous/green wire must be grounded.
7. Based on calculations in compliance with AS60335.2.40 in that location is no minimum safety floor area requirement for the installation of the air conditioners described in this transmission.

Circumspection
All side louvers of the cabinet must remain exposed to the outside of the structure. less than 220mm

Production Dimensions

Installation of the Housing

1. Remove the air conditioner from its packaging, remove fixing screws and slide the air conditioner out of its housing (Refer to Installation Steps).
2. Prepare the hole in the wall so that the bottom of the housing is well supported, the elevation has minimum clearance and the air inlet louvers have clearance as shown below in options A and B. Holes from the outside through to the cavity should be sealed. The housing should gradient down towards the rear by about 5mm to let water formed during operation to drain.
3. Install the housing into the wall and secure. Ensure the foam seals are not damaged. Flash, seal or fill up gaps around the inside and outside to provide satisfactory advent and protection against the weather, insects and rodents.

Notation: Unit may exist supported by a solid frame from beneath or by a hanger from a solid overhead support.

Installation of the unit of measurement into the housing

1. Slide the unit into the housing until it is firmly against the rear of the housing. Care is required to ensure the foam sealing strips on the housing remain in position.
2. Connect the air conditioner to the power and position excess cord length below the air conditioner base.
3. Engage the chassis fixing brackets into the bottom housing track and secure to the base of operations with the screws provided.
4. Remove the front panel from information technology'due south carton and plastic bag and fit every bit per the Installation lnstruction.
5. Switch unit of measurement on. Check for operation of the unit and check for vibration in the installation.
6. Fit the drain pan to the housing and run a drain line to a suitable location if required.

Installing the unit into the wall

Installation Steps

Step one. Remove the front console and the air filter

1. Hold the slot under the front panel, and so lift it up and outwards, and remove the front panel (Meet Fig.1).
2. Pinch the handle under the air filter, bend the filter gently and remove it from the slots (Come across Fig.2).

Step two. Remove the frame.

1. Remove fixing screws from the frame (See Fig.3). Screws tin be in different positions of the frame for different models, commonly there are 2 screws at the rear of the larger units and i screw at the mid front end correct. Smaller units have less screws.
2. Release the front panel lugs on the side of the front end console from the outer frame slots at height, middle and lesser where they meet. Grasp the left corner of the frame's underside, and so loosen the frame (See Fig.4).

Pace 3. Installation.

1. Remove the fixing spiral on the chassis fixing bracket, and so remove the chassis fixing bracket (See Fig.5).
2. Grasp the handle on the chassis and carefully slide the air conditioner out of the cabinet (See Fig.6).
3. Push the unit chassis into the cabinet (See Fig.8).4 Reinstall the chassis fixing bracket removed earlier (Encounter Fig.5).

Install the frame.

1. Install the frame making sure not to jam the ability supply cablevision (See Fig.viii).
2. Fix the screws on the frame.

Footstep 5. Install the air filter and front console.

1. Install the air filter into the frame's slot from upside to underside (See Fig. two).
2. Hang the forepart panel on the frame's elevation edge, then press the forepart panel into the frame edges until yous hear clicks.

Troubleshooting

Troubleshooting Tips
Salvage fourth dimension and money! Review the chart beneath kickoff and you lot may not demand to call for service.

Normal functioning

• You may hear a pinging noise acquired by water being picked up and thrown against the condenser on rainy days or when the humidity is high. This design characteristic helps remove moisture and improve efficiency.
• You may hear the thermostat click when the compressor cycles on and off.
• H2o will collect in the base pan during high humidity or on rainy days. The water may overflow and baste from the outdoor side of the unit.
• The fan may go on to operate when the compressor has cycled off.

Troubleshooting

Warranty

FOR SALES IN Australia AND NEW ZEALAND KELVINATOR WINDOW/WALL AIR CONDITIONER

This document sets out the terms and conditions of the production warranties for Kelvinator Appliances. It is an important certificate. Please go on it with your proof of purchase documents in a safe identify for future reference should there be a manufacturing defect in your Appliance. This warranty is in addition to other rights you lot may have under the Australian Consumer Police.

1. In this warranty:
   • (a) `ACL' or `Australian Consumer Law' means Schedule two to the Competition and Consumer Human activity 2010;
   • (b) `Appliance' means whatsoever Electrolux product purchased past you and accompanied past this document;
   • (c) `ASC' means Electrolux'due south authorised serviced centres;
   • (d) `Kelvinator' is the brand controlled by Electrolux Dwelling Products Pty Ltd of 163 O'Riordan Street, Mascot NSW 2020, ABN 51 004 762 341 in respect of Appliances purchased in Australia and Electrolux (NZ) Limited (collectively "Electrolux") of iii-5 Niall Burgess Route, Mount Wellington, in respect of Appliances purchased in New Zealand;
   • (due east) `Warranty Condition' means:
     • (i) evidence past the customer that the Appliance was installed in accordance with Electrolux installation guidelines as set out in the installation manual;
     • (ii) the Appliance rating is correct for the size and thermal characteristics of the room;
     • (3) the Appliance has been regularly maintained in accordance with Electrolux guidelines equally fix out in the user manual;
     • (4) the Appliance is designed for providing human being comfort and should exist used under ambient atmospheric condition as gear up out in the product specifications and general air quality conditions.
   • (f) `Warranty Menstruum' means the flow specified in clause 3 of this warranty;
   • (m) `you' means the purchaser of the Apparatus not having purchased the Appliance for re-sale, and `your' has a corresponding meaning.
2. Application: This warranty but applies to new Appliances, purchased and used in Australia or New Zealand and is in add-on to (and does not exclude, restrict, or change in any style) other rights and remedies under a constabulary to which the Appliances or services relate, including whatsoever nonexcludable statutory guarantees in Commonwealth of australia and New Zealand.
3. Warranty Period: Subject to these terms and weather condition, this warranty continues for in Australia for a period of sixty months and in New Zealand for a period of 60 months, post-obit the engagement of original buy of the Appliance.
4. Repair or replace warranty: During the Warranty Catamenia, Electrolux or its ASC will, at no extra charge if your Appliance is readily accessible for service, without special equipment and discipline to these terms and weather, repair or replace any parts which it considers to exist defective. Electrolux may, in its absolute discretion, cull whether the remedy offered for a valid warranty merits is repair or replacement. Electrolux or its ASC may use refurbished parts to repair your Appliance. You concord that whatever replaced Appliances or parts become the property of Electrolux.
5. Travel and transportation costs: Subject area to clause seven, Electrolux will carry the reasonable cost of transportation, travel and delivery of the Appliance to and from Electrolux or its ASC. Travel and transportation volition exist arranged past Electrolux as function of any valid warranty claim.
6. Proof of buy is required before you can make a claim under this warranty.
7. Exclusions: You may non make a claim under this warranty unless the defect claimed is due to faulty or defective parts or workmanship. This warranty does not cover:
   • (a) lite globes, batteries, filters or similar perishable parts;
   • (b) parts and Appliances not supplied by Electrolux;
   • (c) cosmetic damage which does not affect the operation of the Appliance;
   • (d) damage to the Appliance caused past:
     • (i) negligence or blow;
     • (ii) misuse or abuse, including failure to properly maintain or service;
     • (iii) improper, negligent or faulty servicing or repair works washed past anyone other than an Electrolux authorised repairer or ASC;
     • (iv) normal wearable and tear;
     • (five) power surges, electrical storm damage or wrong power supply;
     • (vi) incomplete or improper installation;
     • (vii) incorrect, improper or inappropriate operation;
     • (viii) insect or vermin infestation;
     • (nine) failure to comply with any additional instructions supplied with the Appliance; and
     • (10) a breach of the Warranty Conditions.
   • In add-on, Electrolux is non liable under this warranty if:
     • (a) the Appliance has been, or Electrolux reasonably believes that the Appliance has been, used for purposes other than those for which the Apparatus was intended, including where the Appliance has been used for any non-domestic purpose;
     • (b) the Appliance is modified without authority from Electrolux in writing;
     • (c) the Apparatus'southward serial number or warranty seal has been removed or defaced.
8. How to claim under this warranty: To enquire about claiming under this warranty, please follow these steps:
   • (a) advisedly bank check the operating instructions, user manual and the terms of this warranty;
   • (b) have the model and serial number of the Apparatus bachelor;
   • (c) have the proof of purchase (eastward.thousand. an invoice) available;
   • (d) telephone the numbers shown below.
9. Australia: For Appliances and services provided by Electrolux in Australia: Electrolux goods come with guarantees that cannot be excluded under the Australian Consumer Police. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. Yous are also entitled to take the Appliance repaired or replaced if the Appliance fails to be of acceptable quality and the failure does not amount to a major failure. `Acceptable quality' and `major failure' have the aforementioned meaning as referred to in the ACL.
10. New Zealand: For Appliances and services provided past Electrolux in New Zealand, the Appliances come with a guarantee by Electrolux pursuant to the provisions of the Consumer Guarantees Human action, the Sale of Goods Act and the Fair Trading Human action. Where the Appliance was purchased in New Zealand for commercial purposes the Consumer Guarantee Act does not apply.
11. Confidentiality: Y'all accept that if y'all make a warranty claim, Electrolux and its agents including ASC may exchange information in relation to you to enable Electrolux to run across its obligations under this warranty.

Important Observe
Earlier calling for service, please ensure that the steps listed in clause 8 higher up have been followed.

AUSTRALIA

FOR SERVICE or to find the address of your nearest authorised service centre in Australia Please CALL 13 thirteen 49 For the price of a local phone call

FOR SPARE PARTS or to find the address of your nearest spare parts eye in Commonwealth of australia Please CALL 13 13 50 For the cost of a local phone call

NEW ZEALAND

FOR SERVICE or to detect the address of your nearest authorised service centre in New Zealand Please Call 0800 10 66 10

FOR SPARE PARTS or to find the accost of your nearest spare parts middle in New Zealand Please CALL 0800 10 66 20

For more data on all Kelvinator appliances, or for dimension and installation information, call into your retailer, phone or e-mail our customer care squad or visit our website:

Commonwealth of australia phone: 1300 363 640 fax: 1800 350 067 email: [electronic mail protected] web: kelvinator.com.au

NEW ZEALAND phone: 0800 436 245 fax: 0800 225 088 e-mail: [e-mail protected] web: kelvinator.co.nz

Kelvinator.
Nosotros are part of the Electrolux Family.
To add a touch of professional inspiration to your dwelling, visit electrolux.com.au

P/No. 1452635
© 2019 Electrolux Domicile Products Pty Ltd
ABN 51 004 762 341
KMAN_WWE_Jul19

Documents / Resource

kelvinator Window Wall Electronic Room Air Conditioner [pdf] User Manual Window Wall Electronic Room Air Conditioner, KWH20CRE, KWH20HRE, KWH26CRE, KWH26HRE, KWH39CRE, KWH39HRE, KWH53CRE, KWH53HRE, KWH62CRE, KWH62HRE

References

Source: https://manuals.plus/kelvinator/window-wall-electronic-room-air-conditioner-manual

Posted by: goodmanprietry.blogspot.com

Share this post